radiall sma 127-1
TRANSCRIPT
-
8/12/2019 Radiall SMA 127-1
1/60
APPLIED ENGINEERING PRODUCTS104 John W. Murphy Drive P.O. Box 510 New Haven, CT 06513
(203) 776-2813 FAX (203) 776-8294
www.aepconnectors.com e-mail: [email protected]
SMA SeriesSubminiatureRF ConnectorsScrew-on mating
Frequency range DC-18 GHz
High performance
Rugged construction
ONLIN
E
CATA
LOG
-
8/12/2019 Radiall SMA 127-1
2/60
SMA Subminiature ConnectorsClick on any line below to go directly to the appropriate page
APPLIED ENGINEERING PRODUCTS104 John W. Murphy Drive P.O. Box 510 New Haven, CT 06513
(203) 776-2813 FAX (203) 776-8294www.aepconnectors.com e-mail: [email protected]
Contents
Technical Information
Interfaces and specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Cable attachment methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cable ConnectorsPlugs for semi-rigid cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Plugs for flexible cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Jacks for semi-rigid cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Jacks for flexible cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Bulkhead jacks for semi-rigid cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Bulkhead jacks for flexible cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Panel jacks for semi-rigid cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Panel jacks for flexible cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Receptacles
Panel jack receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Receptacles for .025" microstrip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Receptacles for .010" microstrip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Panel plug receptacles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Bulkhead jack receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Knurl mount receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
P.C. board receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Stripline receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Hermetic seal launchers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Adapters
Straight adapters within series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Right angle adapters within series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Tee adapters within series. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Resistive Terminations
Plug resistive termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Cable Assembly Instructions
Connectors for flexible cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Connectors for semi-rigid cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Assembly Tooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Index by AEP Part Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
About AEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Other AEP Product Lines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
2
-
8/12/2019 Radiall SMA 127-1
3/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 3
SMA Connectors
Interface Dimensions
Specifications (MIL-PRF-39012 as applicable)
Materials:
Body components: Stainless steel per ASTM-A-582, type 303.Contacts: Beryllium copper per ASTM-B-196, Condition HT.Insulators:Teflon TFE per ASTM-D-1710.Gaskets: Silicone rubber per ZZ-R-765, Class 2B, grade 65-75.Finish:
Center contacts: Gold plated per current revisionof MIL-PRF-39012*Other metal parts: Gold plated, passivated, or nickel plated tomeet current MIL-PRF-39012 corrosion requirements.*
Electrical:VSWR Straight cable plugs and jacks):
Cable VSWR FrequencyRG-178 1.20 +(.025 x F[GHz]) DC-12.4 GHzRG-316 1.15 +(.020 x F[GHz]) DC-12.4 GHzRG-142 1.15 +(.010 x F[GHz]) DC-12.4 GHzRG-402(1) 1.05 +(.008 x F[GHz]) DC-18 GHzRG-402(2) 1.05 +(.010 x F[GHz]) DC-18 GHzRG-405(1) 1.07 +(.008 x F[GHz]) DC-18 GHzRG-405(2) 1.07 +(.010 x F[GHz]) DC-18 GHz(1)Non-captive contact. (2)Captive contact.
VSWR specifications not applicable to non-cabled connectors.Impedance: 50.Frequency range: DC8, 12.4, or 18 GHz (varies with cable type).Insulation Resistance: 5,000 megohms minimum.
Electrical (continued):
Voltage Rating: 250VRMS @ sea level (RG-178 cable);335VRMS @ sea level (RG-316 cable).Dielectric Withstanding Voltage: Per MIL-STD-202, Method 301.Contact Resistance: 3 milliohms maximum.RF highpot: 335-675 VRMS @ 5-7.5 MHz (varies with cable type).RF leakage: -60 dB min @ 23 GHz.Insertion loss: .44 dB max to 6 GHz.Mechanical:
Force to engage/disengage: 2 pounds max.
Force to engage/disengage (female contacts):(After 5 insertions of .375" diameter pin, .040" min depth)Insertion force for .037 min diameter pin, 2 pounds max.Withdrawal force for .0355" max diameter pin, 1 ounce min.Contact retention: 6 pounds min axial force (captive types).Durability: 500 mating cycles.Environmental (MIL-STD-202):
Temperature range: -65 C to +165 C.Corrosion: Method 101, condition B, 5% salt solution.Vibration (Method 204): Condition B.Mechanical shock (Method 213): Condition B.Thermal shock (Method 107): Condition B.
*These specifications change periodically with updates to MIL-PRF-39012 requirements. Contact factory for latest specifications.
Plug Jack
AEP SMA connectors are available with gold-plated bodies, or with passivated or nickel-plated bodies for
greater economy. The coupling nuts of plug connectors are passivated in all cases.
Our unique mechanical captivation method (see page 5) greatly reduces RF leakage by eliminating epoxy fill
hoes in the connector body.
-
8/12/2019 Radiall SMA 127-1
4/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 4
SMA Cable Attachment MethodsSemi-Rigid Cable
Direct Solder (cable center conductor used as contact): This type of cable attachment ensures the best possible
electrical performance because there are no discontinuities introduced by contact geometry changes. It is bestused in applications not requiring frequent mating and unmating, because the pointed center conductor and
exposed cable jacket will shed metal chips when mated with SMA female connectors.
Direct Solder (with contact and insulator): Although this cable attachment exhibits higher VSWR than typeswithout contacts, it provides an outer conductor that does not have the copper cable jacket exposed to mating
forces. This, along with the beryllium-copper contact, ensures clean interfaces through many mating cycles.
Direct Solder (with captive contact): These connectors haveelectrical performance similar to types with non-captivecontacts, but with faster and easier cable assembly.
The cable is simply stripped and inserted into the connector,and the cable jacket soldered to the connector. The proper
contact gap is automatically maintained, and no contactsoldering is required.
Solder-clamp: This attachment is most useful for rightangle plugs and bulkhead jacks. After the connector is
assembled to the cable jacket, it can be repositionedrelative to the cable by loosening the clamp nut.
Electrical performance is similar to direct-solder plugswith contacts.
-
8/12/2019 Radiall SMA 127-1
5/60
Crimp (captive contact): This attachment methodmechanically captivates the center contact to
eliminate movement during cable flexure or
thermal stress.
Clamp (captive contact): These connectors can
be assembled without special tooling, and arefield replaceable.
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 5
SMA Cable Attachment Methods
SMA Captivation
Flexible Cable
Crimp (non-captive contact): This attachment method provides the best possible electrical performance, andthe fastest assembly. Solder type connectors for flexible cable have the same construction, but add a hole inthe side of the crimp sleeve for soldering the cable braid to the connector. We do not recommend the use of
solder type connectors with flexible cablethe heat from soldering may damage the cable dielectric.
All AEP SMA receptacles and adapters use our unique mechanical
captivation for contacts and insulators. This method providesretention strength to meet MIL-PRF-39012 requirements, and
eliminates RF leakage from epoxy fill holes. The contact barbsand body staking are designed and located to provide electricalperformance that equals or exceeds epoxy-captivated types.
-
8/12/2019 Radiall SMA 127-1
6/60
SMA Cable Plugs for Semi-Rigid CableClick on part number to go directly to cable assembly instructions
Straight Plugs
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 6
Continued on next page
-
8/12/2019 Radiall SMA 127-1
7/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 7
Right Angle Plugs
SMA Cable Plugs for Semi-Rigid CableClick on part number to go directly to cable assembly instructions
Straight Plugs
-
8/12/2019 Radiall SMA 127-1
8/60
-
8/12/2019 Radiall SMA 127-1
9/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 9
GROUP CABLE TYPES
01 RG142, RG223, M17/60, M17/84, M17/158
02 RG178, RG196, M17/93, M17/169
03 RG174, RG179, RG316, M17/113, M17/119, M17/172, M17/189
GROUP CABLE TYPES
06 RG58, RG141, RG303, M17/111, M17/155
19RG174DS, RG316DS, M17/151, M17/152,Times RD-316
GROUP CABLE TYPES
04 RG180, RG195, M17/95
05 RG178DS, RG196DS
Substitute the appropriate cable group number for XX when ordering:
SMA Cable Plugs for Flexible CableClick on part number to go directly to cable assembly instructions
Right Angle Plugs
-
8/12/2019 Radiall SMA 127-1
10/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 10
SMA Cable Jacks for Semi-Rigid CableClick on part number to go directly to cable assembly instructions
Straight Jacks
-
8/12/2019 Radiall SMA 127-1
11/60
-
8/12/2019 Radiall SMA 127-1
12/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 12
SMA Bulkhead Jacks for Semi-Rigid CableClick on part number to go directly to cable assembly instructions
Straight Jacks
Right Angle Jack
-
8/12/2019 Radiall SMA 127-1
13/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 13
SMA Bulkhead Jacks for Flexible CableClick on part number to go directly to cable assembly instructions
Straight Jacks
Right Angle Jack
GROUP CABLE TYPES
01 RG142, RG223, M17/60, M17/84, M17/158
02 RG178, RG196, M17/93, M17/169
03 RG174, RG179, RG316, M17/113, M17/119, M17/172, M17/189
GROUP CABLE TYPES
06 RG58, RG141, RG303, M17/111, M17/155
19RG174DS, RG316DS, M17/151, M17/152,Times RD-316
GROUP CABLE TYPES
04 RG180, RG195, M17/95
05 RG178DS, RG196DS
Substitute the appropriate cable group number for XX when ordering:
-
8/12/2019 Radiall SMA 127-1
14/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 14
SMA Panel Jacks for Semi-Rigid CableClick on part number to go directly to cable assembly instructions
Straight Jacks
-
8/12/2019 Radiall SMA 127-1
15/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 15
GROUP CABLE TYPES
01 RG142, RG223, M17/60, M17/84, M17/158
02 RG178, RG196, M17/93, M17/169
03 RG174, RG179, RG316, M17/113, M17/119, M17/172, M17/189
GROUP CABLE TYPES
06 RG58, RG141, RG303, M17/111, M17/155
19RG174DS, RG316DS, M17/151, M17/152,Times RD-316
GROUP CABLE TYPES
04 RG180, RG195, M17/95
05 RG178DS, RG196DS
Substitute the appropriate cable group number for XX when ordering:
SMA Panel Jacks for Flexible CableClick on part number to go directly to cable assembly instructions
Straight Jacks
-
8/12/2019 Radiall SMA 127-1
16/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 16
SMA Straight Panel Jack ReceptaclesExtended Contact and Insulator
-
8/12/2019 Radiall SMA 127-1
17/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 17
SMA Straight Panel Jack ReceptaclesSolder Pot Contact
-
8/12/2019 Radiall SMA 127-1
18/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 18
SMA Straight Panel Jack ReceptaclesTab Contact
-
8/12/2019 Radiall SMA 127-1
19/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 19
SMA Straight Panel Jack ReceptaclesSlotted Contact
-
8/12/2019 Radiall SMA 127-1
20/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 20
SMA Right Angle Panel Jack ReceptaclesSolder Pot Contact
Tab Contact
-
8/12/2019 Radiall SMA 127-1
21/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 21
SMA Receptacles for .025" Microstrip
Tab Contact
Standard SMA receptacles with tab contacts have the tab milled from a .050" diameter round contact.This .050" diameter is flush with the rear insulator of the connector. When these connectors are used with.025" thick microstrip, a capacitive coupling can be introduced because of the close proximity of the microstrip
ground plane to the outer diameter of the contact.
These receptacles eliminate the coupling by reducing the contact rear diameter to .025". The insulator diameter
at the rear of the connector is reduced to .083" to maintain 50 impedance.
-
8/12/2019 Radiall SMA 127-1
22/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 22
SMA Receptacles for .010" Microstrip
Round Contact
These connectors have .010" diameter contact extensions for good electrical transition to narrowmicrostrip lines. The reduced-diameter insulators are extended beyond the flange to maintain50 impedance through the microstrip package wall. All have captive contacts.
-
8/12/2019 Radiall SMA 127-1
23/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 23
SMA Panel Plug ReceptaclesStraightExtended Contact and Insulator
-
8/12/2019 Radiall SMA 127-1
24/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 24
SMA Panel Plug ReceptaclesStraightSolder Pot Contact
Right AngleSolder Pot Contact
-
8/12/2019 Radiall SMA 127-1
25/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 25
SMA Panel Plug ReceptaclesStraightTab Contact
Right AngleTab Contact
-
8/12/2019 Radiall SMA 127-1
26/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 26
SMA Bulkhead Jack ReceptaclesStraightSolder Pot Contact
Right AngleSolder Pot Contact
-
8/12/2019 Radiall SMA 127-1
27/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 27
SMA Bulkhead Jack ReceptaclesStraightExtended Contact and Insulator
StraightSolder Pot Contact
-
8/12/2019 Radiall SMA 127-1
28/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 28
SMA Knurl Mount Receptacles
Straight JackExtended Contact and Insulator
Straight JackSolder Pot Contact
Straight JackTab Contact
Straight PlugTab Contact
These knurl mount receptacles can provide an economical alternative to flange mounted connectors,and are especially useful in dense packaging applications.
They should be used in panels at least .100" thick.
-
8/12/2019 Radiall SMA 127-1
29/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 29
SMA P.C. Board ReceptaclesStraight Jack
Right Angle Jack
Straight Plug
Right Angle Plug
-
8/12/2019 Radiall SMA 127-1
30/60
Straight Plug
Right Angle Jack
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 30
SMA Stripline ReceptaclesStraight Jacks
-
8/12/2019 Radiall SMA 127-1
31/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 31
SMA Hermetic Seal Launchers
Connector / seal designconnectors for
use with .012.018" diameter pins
Electrical Performance Data
AEP SMA hermetic seal launchers are designed to fithermetic seals with .012" to .036" pin diameters.
Connectors for use with .012.018" pins feature aninternal body structure that compensates electrically for
the stepdown in diameter from the connector interfaceto the seal outer diameter, as shown in the illustration.
These units also incorporate a conductive-elastomer EMIgasket to prevent RF leakage at the interface between
the connector flange and the MIC package.
Connectors for seals with .020" or .036" pin diameters
have straight-though body geometry, and do notuse EMI gaskets.
Passivated stainless steel body finish is standard for this
series; gold-plated bodies are available as an option.
Test setup: Two connectors (P/N 9044-9513-000)
mounted back-to-back on fixture incorporatinghermetic seal (P/N 920-55). Precision SMA plug
termination used as load.
The VSWR plot below is for the connector/fixturecombination; data for a single connector can beextrapolated by taking the square root of the reading
at a given frequency. Insertion loss readings shouldbe divided by two to obtain performance for a
single connector.
Electrical performance in actual use may vary based onthe characteristics of the pin-to-line transition.
VSWR Insertion loss (dB)
See next page for hermetic seal specifications and mounting dimensions.
-
8/12/2019 Radiall SMA 127-1
32/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 32
Hermetic Seal Specifications
Mounting Dimensions
Materials:
All metal parts: Kovar.
Glass: Corning glass as noted:
P/N Glass type
920-55 7052
920-56 7070920-69 7052
920-82 7070920-92 7052
Finish:
All metal parts: Gold plated per MIL-G-45204 type II,grade C, class 1, over nickel per MIL-C-26074, class 1,over copper per MIL-C-14550.
Hermeticity:
Greater than 1 x 10-8 cc/second @ 1 atmosphere.
Solderability:
Per MIL-Std-202, Method 209.
Meniscus:
.005" max.
Pin concentricity:
.003" T.I.R.
Temperature range:
-65250 C.
Impedance:
50 1.
Frequency range:DC-26 GHz.
Insertion loss:
.1 dB max. to 12.4 GHz;
.2 dB max. to 18 GHz;
.25 dB max. to 26 GHz.
VSWR:
Dependent on application.
Voltage rating:
335 VRMS max. @ sea level.
Current:
500 mA.
Dielectric Withstanding Voltage:
1000 VRMS @ sea level.
Insulation resistance:
100K megohms (@25 C)
Notes:
1) Front of seal and solder should be flushto .005" above mounting surface.
2) Diameters (D) in chart are for 50
impedance; Teflon dielectric diametersare for applications which use asupport insulator for the hermetic
seal pin (user option).
Pin D D
Diameter (Air dielectric) (Teflon dielectric).012 .028 .040
.015 .035 .050
.018 .041 .059
.020 .046 .066
-
8/12/2019 Radiall SMA 127-1
33/60
Straight Jacks
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 33
SMA Hermetic Seal LaunchersFor hermetic seals with .012" diameter pins
These units accept hermetic seal pin diameters .011.015"
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
34/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 34
SMA Hermetic Seal LaunchersFor hermetic seals with .012" diameter pins
Straight Jacks
These units accept hermetic seal pin diameters .011.015"
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
35/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 35
SMA Hermetic Seal LaunchersFor hermetic seals with .012" diameter pins
Straight Plugs
These units accept hermetic seal pin diameters .011.015"
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
36/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 36
SMA Hermetic Seal LaunchersFor hermetic seals with .015" diameter pins
Straight Jacks
These units accept hermetic seal pin diameters .014.016"
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
37/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 37
SMA Hermetic Seal LaunchersFor hermetic seals with .015" diameter pins
Straight Jacks
These units accept hermetic seal pin diameters .014.016"
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
38/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 38
SMA Hermetic Seal LaunchersFor hermetic seals with .015" diameter pins
Straight Plugs
These units accept hermetic seal pin diameters .014.016"
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
39/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 39
SMA Hermetic Seal LaunchersFor hermetic seals with .018" diameter pins
Straight Jacks
These units accept hermetic seal pin diameters .016.020"
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
40/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 40
SMA Hermetic Seal LaunchersFor hermetic seals with .018" diameter pins
Straight Jacks
These units accept hermetic seal pin diameters .016.020"
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
41/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 41
SMA Hermetic Seal LaunchersFor hermetic seals with .018" diameter pins
Straight Plugs
These units accept hermetic seal pin diameters .016.020"
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
42/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 42
SMA Hermetic Seal LaunchersFor hermetic seals with .020" diameter pins
Straight Jacks
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
43/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 43
SMA Hermetic Seal LaunchersFor hermetic seals with .020" diameter pins
Straight Jacks
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
44/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 44
SMA Hermetic Seal LaunchersFor hermetic seals with .036" diameter pins
Straight Jacks
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
45/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 45
SMA Hermetic Seal LaunchersFor hermetic seals with .036" diameter pins
Straight Jacks
Hermetic Seal and Accessory Contact
-
8/12/2019 Radiall SMA 127-1
46/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 46
SMA AdaptersStraight Adapters
-
8/12/2019 Radiall SMA 127-1
47/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 47
SMA AdaptersRight Angle Adapters
-
8/12/2019 Radiall SMA 127-1
48/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 48
SMA TerminationsPlug Termination
SMA AdaptersTee Adapters
-
8/12/2019 Radiall SMA 127-1
49/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 49
Body assemblyCompression washerFerruleInsulator
Contact (male orfemale) Backnut
Assemble contact onto cable center conductor.Solder contact to center conductor by heating rear of contact
(do not feed additional solder through inspection hole in contact).
Press ferrule against compression washer.Trim excess braid flush with outer diameter of compression washer
and ferrule.Assemble insulator over cable center conductor and dielectric.
Compression washerFerrule
Backnut
Body assembly
CapInsulator
Solder
Cable Assembly InstructionsClamp type connectors for flexible cable
Straight ConnectorsFlexible Cable
Cable Trim Dimensions
Right Angle ConnectorsFlexible Cable
Parts list
BC
A
Braid J acketCenter conductorDielectric
Trim cable per trim code below; tin end of center conductor.Slide backnut onto cable. Slide compression washer onto cable in
the orientation shown until it stops against cable jacket.Flare cable braid by rotating dielectric and slide ferrule under braid.
1
2
3
Insert cable assembly into body assembly. Tighten to 140150inch-ounces torque. (Hold cable/hardware assembly stationaryand rotate body when tightening.)
4Insert cable assembly into body assembly. Tighten to 140150
inch-ounces torque. (Hold cable/hardware assembly stationaryand rotate body when tightening.)
Solder center conductor into notch in rear of contact with.025.032" diameter chisel-tip soldering iron.
Solder should cover center conductor, but not extend over top ofnotch in contact, or exceed contact diameter.
Press ferrule against compression washer.Trim excess braid flush with outer diameter of compression washer
and ferrule.Assemble insulator over cable center conductor and dielectric.
Trim cable per trim code below; tin end of center conductor.Slide backnut onto cable. Slide compression washer onto cable in
the orientation shown until it stops against cable jacket.Flare cable braid by rotating dielectric and slide ferrule under braid.
1
2
3
Place insulator in body cavity, and press cap into place.Properly assembled cap will be slightly below end of body assembly.
4
Parts list
CONNECTOR TYPE A B C
STRAIGHT CONNECTORS .100 .100 .230
RIGHT ANGLE CONNECTORS .100 .275 .400
-
8/12/2019 Radiall SMA 127-1
50/60
Trim cable per trim code below; tin end of center conductor.Slide heat-shrink tubing and crimp sleeve over cable.Assemble contact onto center conductor, shim to maintain .015" gap
between rear of contact and cable dielectric.
Solder contact to center conductor by heating rear of contact(do not feed additional solder through inspection hole in contact).
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 50
Body assembly Heat-shrink tubing(optional)
Backnut/crimp tail
Insulator
Contact (male orfemale) Crimp sleeve
Assemble insulator and contact onto cable dielectric andcenter conductor.
Solder contact to center conductor by heating rear of contact
(do not feed additional solder through inspection hole in contact).
Position cable so braid touches rear of back nut.Slide crimp sleeve forward to touch rear of back nut.Crimp braid with appropriate die size from chart below.
Body assembly
Contact
Heat-shrink tubing
Crimp sleeve
Straight ConnectorsCaptive Contact
Cable Trim Dimensions
Straight ConnectorsNon-captive Contact
Parts list
BC
A
Braid J acketCenter conductor
Dielectric
Trim cable per trim code below; tin end of center conductor.Slide heat-shrink tubing and crimp sleeve over cable.Flare cable braid by rotating dielectric and slide cable into crimp tail.
1
2
3
Insert cable assembly into body assembly. Tighten to 140150inch-ounces torque. (Hold cable/hardware assembly stationaryand rotate body when tightening.)
Slide shrink tubing over crimp sleeve and shrink to fit.
4
Flare cable braid by rotating dielectric and slide cable into tailof body assembly.
Position cable so braid touches rear step of body assembly.Slide crimp sleeve forward to touch rear of body assembly.Crimp braid with appropriate die size from chart below.
1
2
Slide shrink tubing over crimp sleeve and shrink to fit.
3
Parts list
Crimp Die Sizes
CABLE GROUP HEX DIE SIZE
01 .21302 .128
03 .128
04 .156
05 .128
06 .213
19 .156
Cable Assembly InstructionsCrimp type connectors for flexible cable
CONNECTOR TYPE A B C
Captive contact .100 .470 .720
Non-captive contact .100 .160 .390
.015" gap
-
8/12/2019 Radiall SMA 127-1
51/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 51
Cable Trim Dimensions
BC
A
Braid J acketCenter conductor
Dielectric
Body assembly
CapInsulatorHeat-shrink tubing(optional)
Crimp sleeve
Solder
Right Angle ConnectorsFlexible Cable
Solder center conductor into notch in rear of contact with.025.032" diameter chisel-tip soldering iron.
Solder should cover center conductor, but not extend over top ofnotch in contact, or exceed contact diameter.
Position cable so braid touches rear of body assembly.Slide crimp sleeve forward to touch rear of body assembly.Crimp braid with appropriate die size from chart below.
Trim cable per trim code below; tin end of center conductor.Slide heat-shrink tubing and crimp sleeve over cable.Flare cable braid by rotating dielectric and slide cable into crimp tail.
1
2
3
Place insulator in body cavity, and press cap into place.Properly assembled cap will be slightly below end of body assembly.
Slide shrink tubing over crimp sleeve and shrink to fit.
4
Parts list
Cable Assembly InstructionsCrimp type connectors for flexible cable
CONNECTOR TYPE A B C
RIGHT ANGLE CONNECTORS .100 .230 .500
Crimp Die Sizes
CABLE GROUP HEX DIE SIZE
01 .213
02 .128
03 .128
04 .156
05 .128
06 .213
19 .156
-
8/12/2019 Radiall SMA 127-1
52/60
-
8/12/2019 Radiall SMA 127-1
53/60
Trim cable per trim code below; tin end of center conductor.Shim to maintain proper gap between rear of contact
and cable dielectric.
Solder contact to center conductor by heating rear of contact(do not feed additional solder through inspection hole in contact).
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 53
Body assembly
Contact
.015" gap (for .085" diameter cable)
.010" gap (for .141" diameter cable)
Solder
Slide cable into connector until it stops.Solder cable jacket to connector body.
Straight ConnectorsNon-captive Contact
Cable Trim Dimensions
Straight ConnectorsCaptive Contact
Parts list
BA
J acketCenter conductor
Dielectric
1
2
CONNECTOR TYPE A B
Straight connectors .090 .090
Right angle connectors .080 .170
Cable Assembly InstructionsDirect solder connectors for semi-rigid cable
Insert cable into body assembly until it stops.Solder cable jacket to connector body.
Trim cable per trim code below; chamfer end ofcenter conductor 7090 .1
2
Right Angle Connectors
Body assembly
Solder
Solder
CapInsulator
Place insulator in body cavity, and press cap into place.Properly assembled cap will be slightly below end of body assembly.
Solder center conductor into notch in rear of contact with.025.032" diameter chisel-tip soldering iron.
Solder should cover center conductor, but not extend over topof notch in contact, or exceed contact diameter.
Trim cable per trim code below; tin end of center conductor.Insert trimmed cable into body until jacket bottoms on step insidebody and center conductor is in contact slot.
Solder cable jacket to body assembly.
1
2
3
Parts list
-
8/12/2019 Radiall SMA 127-1
54/60
Trim cable per trim code below; point end of center conductor
to 45 as shown.Slide backnut over cable. Slide body over cable until trimmed end ofcable is flush with front of body.
Solder cable jacket to body. Retrim cable dielectric flush with body ifit has extruded due to heat from soldering.
Assemble gasket into groove on body.
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 54
Coupling nut"C" ring
BodyGasket
SolderGasket
"C" ring
Slide coupling nut forward until it stops and assemble "C" ringinto groove.
P/N 9301-1063-009
Cable Trim Dimensions
Parts list
BA
J acketCenter conductor
Dielectric
1
2
Trim cable per trim code below; point end of center conductor
to 45 as shown.Slide backnut over cable. Slide body over cable until trimmed end ofcable jacket stops against step in body.
Solder cable jacket to body. Retrim cable dielectric flush with body ifit has extruded due to heat from soldering.
Assemble gasket into groove on body.
Coupling nut"C" ring
BodyGasket
SolderGasket
"C" ring
Slide coupling nut forward until it stops and assemble "C" ringinto groove.
Parts list
1
2
P/N 9301-1063-109
Cable Assembly InstructionsDirect solder connectors for semi-rigid cable
CONNECTOR TYPE A B
9301-1063-009 .090 .090
9301-1063-109 .090 .180
-
8/12/2019 Radiall SMA 127-1
55/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 55
Crimp tools
Bulkhead Receptacles
TA-0105
TA-0436
DESCRIPTION AEP P/N
Crimp tool with .128" and .213" hex dies TA-0007
Crimp tool with .156" hex die TA-0071
Crimp tool with .105" and .128" hex dies TA-0105
Crimp tool with .255" and .068" hex dies TA-0190
Crimp tool with .255" hex die TA-0234
Torque Wrench
Capping Press
DESCRIPTION AEP P/N
Torque wrench with 5/16" jaw for SMA
coupling nuts; 8 inch-pounds torqueTA-0397
CP-1
Mounting Dimensions
Assembly Tooling
.257 dia.
.238
.200 typ.
.100 typ.
.063 dia.
.067 dia. min. (typ.)
P.C. Board Receptacles
DESCRIPTION AEP P/N
Capping tool (arbor press) with base for Contact
SMA right angle plugs Factory
Capping tool (arbor press) with base for Contact
SMA right angle jacks Factory
-
8/12/2019 Radiall SMA 127-1
56/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 56
Index by Part Number
Numbers ending with -0XX indicate connectors with various types on specified page.Continued on next page
P / N P a g e
5 9 0 3 -1 5 0 3 -0 0 0 . . . . . . . . 48
5 9 0 3 -9 5 0 3 -0 0 0 . . . . . . . . 48
5 9 0 5 -1 5 0 3 -0 0 0 . . . . . . . . 48
5 9 0 5 -9 5 0 3 -0 0 0 . . . . . . . . 48
5 9 0 9 -1 1 0 3 -0 0 0 . . . . . . . . 46
5 9 0 9 -9 1 0 3 -0 0 0 . . . . . . . . 46
5 9 1 6 -1 1 0 3 -6 0 3 . . . . . . . . 46
5 9 1 6 -9 1 0 3 -6 0 3 . . . . . . . . 46
5 9 1 7 -1 1 0 3 -0 0 0 . . . . . . . . 46
5 9 1 7 -9 1 0 3 -0 0 0 . . . . . . . . 46
5 9 1 8 -1 1 0 3 -0 0 0 . . . . . . . . 46
5 9 1 8 -9 1 0 3 -0 0 0 . . . . . . . . 46
5 9 1 9 -1 5 0 3 -0 0 0 . . . . . . . . 47
5 9 1 9 -1 5 0 3 -0 0 1 . . . . . . . . 47
5 9 1 9 -1 5 0 3 -0 0 3 . . . . . . . . 47
5 9 1 9 -9 5 0 3 -0 0 0 . . . . . . . . 47
5 9 1 9 -9 5 0 3 -0 0 1 . . . . . . . . 475 9 1 9 -9 5 0 3 -0 0 3 . . . . . . . . 47
9 0 01 - 10 2 3- 0 XX . . . . . . . . 8
9 0 01 - 10 3 3- 0 XX . . . . . . . . 8
9 0 01 - 90 2 3- 0 XX . . . . . . . . 8
9 0 0 2 - 1 0 2 3 - 0 X X . . . . . . . . 1 1
9 0 0 2 - 1 0 3 3 - 0 X X . . . . . . . . 1 1
9 0 0 2 - 9 0 2 3 - 0 X X . . . . . . . . 1 1
9 0 0 3 - 1 2 1 3 - 0 X X . . . . . . . . 3 0
9 0 0 3 - 9 2 1 3 - 0 X X . . . . . . . . 3 0
9 0 0 4 -1 1 1 3 -0 0 0 . . . . . . . . 16
9 0 0 4 -1 2 1 3 -0 0 0 . . . . . . . . 16
9 0 0 4 -9 1 1 3 -0 0 0 . . . . . . . . 169 0 0 4 -9 2 1 3 -0 0 0 . . . . . . . . 16
9 0 0 7 -1 1 1 3 -0 0 0 . . . . . . . . 16
9 0 0 7 -1 2 1 3 -0 0 0 . . . . . . . . 16
9 0 0 7 -9 1 1 3 -0 0 0 . . . . . . . . 16
9 0 0 7 -9 2 1 3 -0 0 0 . . . . . . . . 16
9 0 0 8 -1 1 1 3 -0 0 0 . . . . . . . . 16
9 0 0 8 -1 2 1 3 -0 0 0 . . . . . . . . 16
9 0 0 8 -9 1 1 3 -0 0 0 . . . . . . . . 16
9 0 0 8 -9 2 1 3 -0 0 0 . . . . . . . . 16
9 0 0 9 -1 1 1 3 -0 0 0 . . . . . . . . 23
9 0 0 9 -1 2 1 3 -0 0 0 . . . . . . . . 23
9 0 0 9 -9 1 1 3 -0 0 0 . . . . . . . . 23
9 0 0 9 -9 2 1 3 -0 0 0 . . . . . . . . 23
9 0 1 3 -1 1 1 3 -0 0 0 . . . . . . . . 27
9 0 1 3 -9 1 1 3 -0 0 0 . . . . . . . . 27
9 0 3 0 - 1 0 2 3 - 0 X X . . . . . . . . 1 3
9 0 3 0 - 1 0 3 3 - 0 X X . . . . . . . . 1 3
9 0 3 0 - 9 0 2 3 - 0 X X . . . . . . . . 1 3
P / N P a g e
9 0 3 1 - 1 0 2 3 - 0 X X . . . . . . . . 1 5
9 0 3 1 - 1 0 3 3 - 0 X X . . . . . . . . 1 5
9 0 3 1 - 9 0 2 3 - 0 X X . . . . . . . . 1 5
9 0 3 3 -1 1 1 3 -0 0 0 . . . . . . . . 2 8
9 0 3 3 -1 2 1 3 -0 0 0 . . . . . . . . 2 8
9 0 3 3 -9 1 1 3 -0 0 0 . . . . . . . . 2 8
9 0 3 3 -9 2 1 3 -0 0 0 . . . . . . . . 2 8
9 0 3 4 - 1 2 1 3 - 0 X X . . . . . . . . 3 0
9 0 3 4 - 9 2 1 3 - 0 X X . . . . . . . . 3 0
9 0 3 5 - 1 5 1 3 - 0 X X . . . . . . . . 3 0
9 0 3 5 - 9 5 1 3 - 0 X X . . . . . . . . 3 0
9 0 43 - 15 2 3- 0 XX . . . . . . . . 9
9 0 43 - 15 3 3- 0 XX . . . . . . . . 9
9 0 43 - 95 2 3- 0 XX . . . . . . . . 9
9 0 4 4 -9 5 1 3 -0 0 0 . . . . . . . . 3 4
9 0 4 4 -9 5 1 3 -0 0 1 . . . . . . . . 3 7
9 0 4 5 -9 5 1 3 -0 0 0 . . . . . . . . 3 39 0 4 5 -9 5 1 3 -0 0 1 . . . . . . . . 3 6
9 0 4 6 -9 5 1 3 -0 0 0 . . . . . . . . 3 5
9 0 4 6 -9 5 1 3 -0 0 1 . . . . . . . . 3 8
9 0 4 7 -9 5 1 3 -0 0 0 . . . . . . . . 3 5
9 0 4 7 -9 5 1 3 -0 0 1 . . . . . . . . 3 8
9 0 4 8 -9 5 1 3 -0 0 0 . . . . . . . . 4 0
9 0 4 9 -9 5 1 3 -0 0 0 . . . . . . . . 3 9
9 0 5 0 -9 5 1 3 -0 0 0 . . . . . . . . 4 1
9 0 5 1 -9 5 1 3 -0 0 0 . . . . . . . . 4 1
9 0 5 5 -1 1 1 3 -0 0 0 . . . . . . . . 2 3
9 0 5 5 -1 2 1 3 -0 0 0 . . . . . . . . 2 3
9 0 5 5 -9 1 1 3 -0 0 0 . . . . . . . . 2 39 0 5 5 -9 2 1 3 -0 0 0 . . . . . . . . 2 3
9 0 5 6 -1 1 1 3 -0 0 0 . . . . . . . . 2 7
9 0 5 6 -9 1 1 3 -0 0 0 . . . . . . . . 2 7
9 0 6 2 -9 5 1 3 -0 0 0 . . . . . . . . 3 3
9 0 6 2 -9 5 1 3 -0 0 1 . . . . . . . . 3 6
9 0 6 8 -9 5 1 3 -0 0 0 . . . . . . . . 3 9
9 0 7 4 -9 5 1 3 -0 0 0 . . . . . . . . 3 9
9 0 7 6 -1 1 1 3 -0 0 0 . . . . . . . . 1 6
9 0 7 6 -1 2 1 3 -0 0 0 . . . . . . . . 1 6
9 0 7 6 -9 1 1 3 -0 0 0 . . . . . . . . 1 6
9 0 7 6 -9 2 1 3 -0 0 0 . . . . . . . . 1 6
9 0 7 9 -9 5 1 3 -0 0 0 . . . . . . . . 3 3
9 0 7 9 -9 5 1 3 -0 0 1 . . . . . . . . 3 6
9 0 8 0 -9 5 1 3 -0 0 0 . . . . . . . . 3 4
9 0 8 0 -9 5 1 3 -0 0 1 . . . . . . . . 3 7
9 0 8 1 -9 5 1 3 -0 0 0 . . . . . . . . 4 0
9 1 01 - 15 7 3- 0 XX . . . . . . . . 8
9 1 01 - 95 7 3- 0 XX . . . . . . . . 8
P / N P a g e
9 1 0 2 - 1 5 7 3 - 0 X X . . . . . . . . 1 1
9 1 0 2 - 9 5 7 3 - 0 X X . . . . . . . . 1 1
9 1 0 4 -1 1 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 4 -1 2 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 4 -9 1 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 4 -9 2 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 7 -1 1 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 7 -1 2 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 7 -9 1 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 7 -9 2 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 8 -1 1 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 8 -1 2 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 8 -9 1 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 8 -9 2 1 3 - 00 0 . . . . . . . . 1 8
9 1 0 9 -1 1 1 3 - 00 0 . . . . . . . . 2 5
9 1 0 9 -1 2 1 3 - 00 0 . . . . . . . . 2 5
9 1 0 9 -9 1 1 3 - 00 0 . . . . . . . . 2 59 1 0 9 -9 2 1 3 - 00 0 . . . . . . . . 2 5
9 1 1 4 -1 1 1 3 - 00 0 . . . . . . . . 2 1
9 1 1 4 -9 1 1 3 - 00 0 . . . . . . . . 2 1
9 1 1 7 -1 1 1 3 - 00 0 . . . . . . . . 2 1
9 1 1 7 -9 1 1 3 - 00 0 . . . . . . . . 2 1
9 1 1 8 -1 1 1 3 - 00 0 . . . . . . . . 2 1
9 1 1 8 -9 1 1 3 - 00 0 . . . . . . . . 2 1
9 1 2 4 -1 5 1 3 - 00 0 . . . . . . . . 2 0
9 1 2 4 -9 5 1 3 - 00 0 . . . . . . . . 2 0
9 1 2 6 -1 5 1 3 - 00 0 . . . . . . . . 2 0
9 1 2 6 -9 5 1 3 - 00 0 . . . . . . . . 2 0
9 1 3 0 - 1 5 7 3 - 0 X X . . . . . . . . 1 39 1 3 0 - 9 5 7 3 - 0 X X . . . . . . . . 1 3
9 1 3 1 - 1 5 7 3 - 0 X X . . . . . . . . 1 5
9 1 3 1 - 9 5 7 3 - 0 X X . . . . . . . . 1 5
9 1 3 3 -1 1 1 3 - 00 0 . . . . . . . . 2 8
9 1 3 3 -1 2 1 3 - 00 0 . . . . . . . . 2 8
9 1 3 3 -9 1 1 3 - 00 0 . . . . . . . . 2 8
9 1 3 3 -9 2 1 3 - 00 0 . . . . . . . . 2 8
9 1 3 9 -1 1 1 3 - 00 0 . . . . . . . . 2 8
9 1 3 9 -1 2 1 3 - 00 0 . . . . . . . . 2 8
9 1 3 9 -9 1 1 3 - 00 0 . . . . . . . . 2 8
9 1 3 9 -9 2 1 3 - 00 0 . . . . . . . . 2 8
9 1 4 4 -9 5 1 3 - 00 0 . . . . . . . . 3 4
9 1 4 4 -9 5 1 3 - 00 1 . . . . . . . . 3 7
9 1 4 5 -9 5 1 3 - 00 0 . . . . . . . . 3 3
9 1 4 5 -9 5 1 3 - 00 1 . . . . . . . . 3 6
9 1 4 6 -9 5 1 3 - 00 0 . . . . . . . . 3 5
9 1 4 6 -9 5 1 3 - 00 1 . . . . . . . . 3 8
9 1 4 7 -9 5 1 3 - 00 0 . . . . . . . . 3 5
-
8/12/2019 Radiall SMA 127-1
57/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 57
Index by Part Number
P / N P a g e
9 1 4 7 -9 5 1 3 -0 0 1 . . . . . . . . 38
9 1 4 8 -9 5 1 3 -0 0 0 . . . . . . . . 40
9 1 4 9 -9 5 1 3 -0 0 0 . . . . . . . . 39
9 1 5 0 -9 5 1 3 -0 0 0 . . . . . . . . 41
9 1 5 1 -9 5 1 3 -0 0 0 . . . . . . . . 41
9 1 5 4 -1 5 1 3 -0 0 0 . . . . . . . . 25
9 1 5 4 -9 5 1 3 -0 0 0 . . . . . . . . 25
9 1 5 5 -1 1 1 3 -0 0 0 . . . . . . . . 25
9 1 5 5 -1 2 1 3 -0 0 0 . . . . . . . . 25
9 1 5 5 -9 1 1 3 -0 0 0 . . . . . . . . 25
9 1 5 5 -9 2 1 3 -0 0 0 . . . . . . . . 25
9 1 6 2 -9 5 1 3 -0 0 0 . . . . . . . . 33
9 1 6 2 -9 5 1 3 -0 0 1 . . . . . . . . 36
9 1 6 3 -1 1 1 3 -0 0 0 . . . . . . . . 21
9 1 6 3 -9 1 1 3 -0 0 0 . . . . . . . . 21
9 1 6 8 -9 5 1 3 -0 0 0 . . . . . . . . 39
9 1 7 4 -9 5 1 3 -0 0 0 . . . . . . . . 399 1 7 6 -1 1 1 3 -0 0 0 . . . . . . . . 18
9 1 7 6 -1 2 1 3 -0 0 0 . . . . . . . . 18
9 1 7 6 -9 1 1 3 -0 0 0 . . . . . . . . 18
9 1 7 6 -9 2 1 3 -0 0 0 . . . . . . . . 18
9 1 7 9 -9 5 1 3 -0 0 0 . . . . . . . . 33
9 1 7 9 -9 5 1 3 -0 0 1 . . . . . . . . 36
9 1 8 0 -9 5 1 3 -0 0 0 . . . . . . . . 34
9 1 8 0 -9 5 1 3 -0 0 1 . . . . . . . . 37
9 1 8 1 -9 5 1 3 -0 0 0 . . . . . . . . 40
9 2 0- 5 5 . . . . . . . . . . . . . 3 3
9 2 0- 5 6 . . . . . . . . . . . . . 3 9
9 2 0- 6 9 . . . . . . . . . . . . . 4 29 2 0- 8 2 . . . . . . . . . . . . . 3 6
9 2 0- 9 2 . . . . . . . . . . . . . 4 4
9 2 01 - 15 5 3- 0 XX . . . . . . . . 8
9 2 01 - 95 5 3- 0 XX . . . . . . . . 8
9 2 0 2 - 1 5 5 3 - 0 X X . . . . . . . . 1 1
9 2 0 2 - 9 5 5 3 - 0 X X . . . . . . . . 1 1
9 2 0 4 - 1 1 1 3 - 0 X X . . . . . . . . 1 9
9 2 0 4 - 1 2 1 3 - 0 X X . . . . . . . . 1 9
9 2 0 4 - 9 1 1 3 - 0 X X . . . . . . . . 1 9
9 2 0 4 - 9 2 1 3 - 0 X X . . . . . . . . 1 9
9 2 0 8 - 1 1 1 3 - 0 X X . . . . . . . . 1 9
9 2 0 8 - 1 2 1 3 - 0 X X . . . . . . . . 1 9
9 2 0 8 - 9 1 1 3 - 0 X X . . . . . . . . 1 9
9 2 0 8 - 9 2 1 3 - 0 X X . . . . . . . . 1 9
9 2 3 0 - 1 5 5 3 - 0 X X . . . . . . . . 1 3
9 2 3 0 - 9 5 5 3 - 0 X X . . . . . . . . 1 3
9 2 3 1 - 1 5 5 3 - 0 X X . . . . . . . . 1 5
9 2 3 1 - 9 5 5 3 - 0 X X . . . . . . . . 1 5
P / N P a g e
9 2 43 - 15 5 3- 0 XX . . . . . . . . 9
9 2 43 - 95 5 3- 0 XX . . . . . . . . 9
9 2 4 4 -9 5 1 3 -0 0 0 . . . . . . . . 3 4
9 2 4 4 -9 5 1 3 -0 0 1 . . . . . . . . 3 7
9 2 4 5 -9 5 1 3 -0 0 0 . . . . . . . . 3 3
9 2 4 5 -9 5 1 3 -0 0 1 . . . . . . . . 3 6
9 2 4 6 -9 5 1 3 -0 0 0 . . . . . . . . 3 5
9 2 4 6 -9 5 1 3 -0 0 1 . . . . . . . . 3 8
9 2 4 7 -9 5 1 3 -0 0 0 . . . . . . . . 3 5
9 2 4 7 -9 5 1 3 -0 0 1 . . . . . . . . 3 8
9 2 4 8 -9 5 1 3 -0 0 0 . . . . . . . . 4 0
9 2 4 9 -9 5 1 3 -0 0 0 . . . . . . . . 3 9
9 2 5 0 -9 5 1 3 -0 0 0 . . . . . . . . 4 1
9 2 5 1 -9 5 1 3 -0 0 0 . . . . . . . . 4 1
9 2 6 2 -9 5 1 3 -0 0 0 . . . . . . . . 3 3
9 2 6 2 -9 5 1 3 -0 0 1 . . . . . . . . 3 6
9 2 6 8 -9 5 1 3 -0 0 0 . . . . . . . . 3 99 2 7 4 -9 5 1 3 -0 0 0 . . . . . . . . 3 9
9 2 7 9 -9 5 1 3 -0 0 0 . . . . . . . . 3 3
9 2 7 9 -9 5 1 3 -0 0 1 . . . . . . . . 3 6
9 2 8 0 -9 5 1 3 -0 0 0 . . . . . . . . 3 4
9 2 8 0 -9 5 1 3 -0 0 1 . . . . . . . . 3 7
9 2 8 1 -9 5 1 3 -0 0 0 . . . . . . . . 4 0
9 3 0 1 - 1 0 6 3 - 0 0 9 . . . . . . . . . 6
9 3 0 1 - 1 0 6 3 - 1 0 9 . . . . . . . . . 6
9 3 0 1 - 7 0 6 3 - 0 0 9 . . . . . . . . . 6
9 3 0 1 - 7 0 6 3 - 1 0 9 . . . . . . . . . 6
9 3 0 4 -1 1 1 3 -0 1 3 . . . . . . . . 2 2
9 3 0 4 -1 1 1 3 -0 1 4 . . . . . . . . 2 29 3 0 4 -9 1 1 3 -0 1 3 . . . . . . . . 2 2
9 3 0 4 -9 1 1 3 -0 1 4 . . . . . . . . 2 2
9 3 0 7 -1 1 1 3 -0 0 1 . . . . . . . . 2 2
9 3 0 7 -1 1 1 3 -0 0 2 . . . . . . . . 2 2
9 3 0 7 -9 1 1 3 -0 0 1 . . . . . . . . 2 2
9 3 0 7 -9 1 1 3 -0 0 2 . . . . . . . . 2 2
9 3 0 8 -1 1 1 3 -0 0 1 . . . . . . . . 2 2
9 3 0 8 -1 1 1 3 -0 0 3 . . . . . . . . 2 2
9 3 0 8 -9 1 1 3 -0 0 1 . . . . . . . . 2 2
9 3 0 8 -9 1 1 3 -0 0 3 . . . . . . . . 2 2
9 3 4 4 -9 5 1 3 -0 0 0 . . . . . . . . 3 4
9 3 4 4 -9 5 1 3 -0 0 0 . . . . . . . . 3 9
9 3 4 4 -9 5 1 3 -0 0 1 . . . . . . . . 3 7
9 3 4 5 -9 5 1 3 -0 0 0 . . . . . . . . 3 3
9 3 4 5 -9 5 1 3 -0 0 1 . . . . . . . . 3 6
9 3 4 6 -9 5 1 3 -0 0 0 . . . . . . . . 3 5
9 3 4 6 -9 5 1 3 -0 0 1 . . . . . . . . 3 8
9 3 4 7 -9 5 1 3 -0 0 0 . . . . . . . . 3 5
P / N P a g e
9 3 4 7 -9 5 1 3 - 00 1 . . . . . . . . 3 8
9 3 4 8 -9 5 1 3 - 00 0 . . . . . . . . 4 0
9 3 5 0 -9 5 1 3 - 00 0 . . . . . . . . 4 1
9 3 5 1 -9 5 1 3 - 00 0 . . . . . . . . 4 1
9 3 6 2 -9 5 1 3 - 00 0 . . . . . . . . 3 3
9 3 6 2 -9 5 1 3 - 00 1 . . . . . . . . 3 6
9 3 6 8 -9 5 1 3 - 00 0 . . . . . . . . 3 9
9 3 7 4 -9 5 1 3 - 00 0 . . . . . . . . 3 9
9 3 7 6 -1 1 1 3 - 00 1 . . . . . . . . 2 2
9 3 7 6 -1 1 1 3 - 00 2 . . . . . . . . 2 2
9 3 7 6 -9 1 1 3 - 00 1 . . . . . . . . 2 2
9 3 7 6 -9 1 1 3 - 00 2 . . . . . . . . 2 2
9 3 7 9 -9 5 1 3 - 00 0 . . . . . . . . 3 3
9 3 7 9 -9 5 1 3 - 00 1 . . . . . . . . 3 6
9 3 8 0 -9 5 1 3 - 00 0 . . . . . . . . 3 4
9 3 8 0 -9 5 1 3 - 00 1 . . . . . . . . 3 7
9 3 8 1 -9 5 1 3 - 00 0 . . . . . . . . 4 09 4 0 1 - 1 0 8 3 - 0 1 0 . . . . . . . . . 6
9 4 0 1 - 1 0 8 3 - 1 0 9 . . . . . . . . . 6
9 4 0 1 - 1 0 8 3 - 2 1 0 . . . . . . . . . 7
9 4 0 1 - 1 5 8 3 - 0 1 0 . . . . . . . . . 6
9 4 0 1 - 1 5 8 3 - 1 0 9 . . . . . . . . . 6
9 4 0 1 - 7 0 8 3 - 0 1 0 . . . . . . . . . 6
9 4 0 1 - 7 0 8 3 - 1 0 9 . . . . . . . . . 6
9 4 0 1 - 7 0 8 3 - 2 1 0 . . . . . . . . . 7
9 4 0 1 - 7 5 8 3 - 0 1 0 . . . . . . . . . 6
9 4 0 1 - 7 5 8 3 - 1 0 9 . . . . . . . . . 6
9 4 0 2 -1 0 8 3 - 00 9 . . . . . . . . 1 0
9 4 0 2 -1 0 8 3 - 01 0 . . . . . . . . 1 09 4 0 2 -1 5 8 3 - 00 9 . . . . . . . . 1 0
9 4 0 2 -1 5 8 3 - 01 0 . . . . . . . . 1 0
9 4 0 2 -7 0 8 3 - 00 9 . . . . . . . . 1 0
9 4 0 2 -7 0 8 3 - 01 0 . . . . . . . . 1 0
9 4 0 2 -7 5 8 3 - 00 9 . . . . . . . . 1 0
9 4 0 2 -7 5 8 3 - 01 0 . . . . . . . . 1 0
9 4 0 4 -1 1 1 3 - 00 0 . . . . . . . . 1 7
9 4 0 4 -9 1 1 3 - 00 0 . . . . . . . . 1 7
9 4 0 7 -1 1 1 3 - 00 0 . . . . . . . . 1 7
9 4 0 7 -9 1 1 3 - 00 0 . . . . . . . . 1 7
9 4 0 8 -1 1 1 3 - 00 0 . . . . . . . . 1 7
9 4 0 8 -1 1 1 3 - 00 2 . . . . . . . . 1 7
9 4 0 8 -9 1 1 3 - 00 0 . . . . . . . . 1 7
9 4 0 8 -9 1 1 3 - 00 2 . . . . . . . . 1 7
9 4 0 9 -1 1 1 3 - 00 0 . . . . . . . . 2 4
9 4 0 9 -9 1 1 3 - 00 0 . . . . . . . . 2 4
9 4 1 2 -1 1 1 3 - 00 0 . . . . . . . . 2 6
9 4 1 2 -9 1 1 3 - 00 0 . . . . . . . . 2 6
Numbers ending with -0XX indicate connectors with various types on specified page.Continued on next page
-
8/12/2019 Radiall SMA 127-1
58/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 58
Index by Part Number
P / N P a g e
9 4 1 3 -1 1 1 3 -0 0 0 . . . . . . . . 27
9 4 1 3 -9 1 1 3 -0 0 0 . . . . . . . . 27
9 4 2 2 -1 1 1 3 -0 0 0 . . . . . . . . 26
9 4 2 2 -9 1 1 3 -0 0 0 . . . . . . . . 26
9 4 2 4 -1 5 1 3 -0 0 0 . . . . . . . . 20
9 4 2 4 -9 5 1 3 -0 0 0 . . . . . . . . 20
9 4 2 5 -1 5 1 3 -0 0 0 . . . . . . . . 20
9 4 2 5 -9 5 1 3 -0 0 0 . . . . . . . . 20
9 4 3 1 -1 0 8 3 -0 0 9 . . . . . . . . 14
9 4 3 1 -1 0 8 3 -0 1 0 . . . . . . . . 14
9 4 3 1 -1 5 8 3 -0 0 9 . . . . . . . . 14
9 4 3 1 -1 5 8 3 -0 1 0 . . . . . . . . 14
9 4 3 1 -7 0 8 3 -0 0 9 . . . . . . . . 14
9 4 3 1 -7 0 8 3 -0 1 0 . . . . . . . . 14
9 4 3 1 -7 5 8 3 -0 0 9 . . . . . . . . 14
9 4 3 1 -7 5 8 3 -0 1 0 . . . . . . . . 14
9 4 3 2 -1 1 1 3 -0 0 0 . . . . . . . . 26
9 4 3 2 -9 1 1 3 -0 0 0 . . . . . . . . 26
9 4 3 3 -1 1 1 3 -0 0 0 . . . . . . . . 28
9 4 3 3 -9 1 1 3 -0 0 0 . . . . . . . . 28
9 4 4 1 -1 0 8 3 -0 0 9 . . . . . . . . 14
9 4 4 1 -1 0 8 3 -0 1 0 . . . . . . . . 14
9 4 4 1 -1 5 8 3 -0 0 9 . . . . . . . . 14
9 4 4 1 -1 5 8 3 -0 1 0 . . . . . . . . 14
9 4 4 1 -7 0 8 3 -0 0 9 . . . . . . . . 14
9 4 4 1 -7 0 8 3 -0 1 0 . . . . . . . . 14
9 4 4 1 -7 5 8 3 -0 0 9 . . . . . . . . 14
9 4 4 1 -7 5 8 3 -0 1 0 . . . . . . . . 149 4 4 3 - 1 5 6 3 - 0 0 9 . . . . . . . . . 7
9 4 4 3 - 1 5 6 3 - 0 1 0 . . . . . . . . . 7
9 4 4 3 - 7 5 6 3 - 0 0 9 . . . . . . . . . 7
9 4 4 3 - 7 5 6 3 - 0 1 0 . . . . . . . . . 7
9 4 5 3 -1 0 8 3 -0 0 9 . . . . . . . . 12
9 4 5 3 -1 0 8 3 -0 1 0 . . . . . . . . 12
9 4 5 3 -1 5 8 3 -0 0 9 . . . . . . . . 12
9 4 5 3 -1 5 8 3 -0 1 0 . . . . . . . . 12
9 4 5 3 -7 0 8 3 -0 0 9 . . . . . . . . 12
9 4 5 3 -7 0 8 3 -0 1 0 . . . . . . . . 12
9 4 5 3 -7 5 8 3 -0 0 9 . . . . . . . . 12
9 4 5 3 -7 5 8 3 -0 1 0 . . . . . . . . 129 4 5 4 -1 5 1 3 -0 0 0 . . . . . . . . 24
9 4 5 4 -9 5 1 3 -0 0 0 . . . . . . . . 24
9 4 5 5 -1 1 1 3 -0 0 0 . . . . . . . . 24
9 4 5 5 -9 1 1 3 -0 0 0 . . . . . . . . 24
9 4 5 6 -1 1 1 3 -0 0 2 . . . . . . . . 27
P / N P a g e
9 4 5 6 -9 1 1 3 -0 0 2 . . . . . . . . 2 7
9 4 7 6 -1 1 1 3 -0 0 0 . . . . . . . . 1 7
9 4 7 6 -9 1 1 3 -0 0 0 . . . . . . . . 1 7
9 5 0 1 - 1 5 9 3 - 0 0 9 . . . . . . . . . 7
9 5 0 1 - 1 5 9 3 - 0 1 0 . . . . . . . . . 7
9 5 0 1 - 9 5 9 3 - 0 0 9 . . . . . . . . . 7
9 5 0 1 - 9 5 9 3 - 0 1 0 . . . . . . . . . 7
9 5 0 2 - 1 5 9 3 - 0 0 9 . . . . . . . . . 7
9 5 0 2 - 1 5 9 3 - 0 1 0 . . . . . . . . . 7
9 5 0 2 - 9 5 9 3 - 0 0 9 . . . . . . . . . 7
9 5 0 2 - 9 5 9 3 - 0 1 0 . . . . . . . . . 7
9 5 0 4 -9 1 1 3 -0 0 9 . . . . . . . . 4 4
9 5 0 4 -9 1 1 3 -0 3 1 . . . . . . . . 4 2
9 5 0 4 -9 1 1 3 -0 3 4 . . . . . . . . 4 2
9 5 0 4 -9 1 1 3 -0 3 5 . . . . . . . . 4 4
9 5 0 7 -9 1 1 3 -0 0 3 . . . . . . . . 4 2
9 5 0 7 -9 1 1 3 -0 0 4 . . . . . . . . 4 2
9 5 0 7 -9 1 1 3 -0 0 5 . . . . . . . . 4 4
9 5 0 7 -9 1 1 3 -0 0 6 . . . . . . . . 4 4
9 5 0 8 -9 1 1 3 -0 0 1 . . . . . . . . 4 5
9 5 0 8 -9 1 1 3 -0 0 2 . . . . . . . . 4 3
9 5 0 8 -9 1 1 3 -0 0 3 . . . . . . . . 4 3
9 5 0 8 -9 1 1 3 -0 1 1 . . . . . . . . 4 5
9 5 1 3 -9 1 1 3 -0 0 8 . . . . . . . . 4 5
9 5 1 3 -9 1 1 3 -0 0 9 . . . . . . . . 4 3
9 5 1 3 -9 1 1 3 -0 1 2 . . . . . . . . 4 3
9 5 1 3 -9 1 1 3 -0 1 3 . . . . . . . . 4 5
9 5 3 0 -1 5 9 3 -0 0 9 . . . . . . . . 1 29 5 3 0 -1 5 9 3 -0 1 0 . . . . . . . . 1 2
9 5 3 0 -9 5 9 3 -0 0 9 . . . . . . . . 1 2
9 5 3 0 -9 5 9 3 -0 1 0 . . . . . . . . 1 2
9 5 3 3 -9 1 1 3 -0 0 1 . . . . . . . . 4 5
9 5 3 3 -9 1 1 3 -0 0 2 . . . . . . . . 4 3
9 5 3 3 -9 1 1 3 -0 0 3 . . . . . . . . 4 3
9 5 3 3 -9 1 1 3 -0 0 4 . . . . . . . . 4 5
9 5 4 3 - 1 5 9 3 - 0 0 9 . . . . . . . . . 7
9 5 4 3 - 1 5 9 3 - 0 1 0 . . . . . . . . . 7
9 5 4 3 - 9 5 9 3 - 0 0 9 . . . . . . . . . 7
9 5 4 3 - 9 5 9 3 - 0 1 0 . . . . . . . . . 7
9 5 7 6 -9 1 1 3 -0 0 1 . . . . . . . . 4 29 5 7 6 -9 1 1 3 -0 0 2 . . . . . . . . 4 2
9 5 7 6 -9 1 1 3 -0 0 3 . . . . . . . . 4 4
9 5 7 6 -9 1 1 3 -0 0 4 . . . . . . . . 4 4
9 6 0 9 -1 5 1 3 -0 0 0 . . . . . . . . 2 6
9 6 0 9 -9 5 1 3 -0 0 0 . . . . . . . . 2 6
P / N P a g e
9 6 1 0 - 1 2 1 3 - 0 X X . . . . . . . . 3 0
9 6 1 0 - 9 2 1 3 - 0 X X . . . . . . . . 3 0
9 6 1 3 - 1 5 2 3 - 0 X X . . . . . . . . 1 3
9 6 1 3 -1 5 6 3 - 00 9 . . . . . . . . 1 2
9 6 1 3 -1 5 6 3 - 01 0 . . . . . . . . 1 2
9 6 1 3 -7 5 6 3 - 00 9 . . . . . . . . 1 2
9 6 1 3 -7 5 6 3 - 01 0 . . . . . . . . 1 2
9 6 1 3 - 9 5 2 3 - 0 X X . . . . . . . . 1 3
9 6 2 0 -9 0 0 3 - 15 1 . . . . . . . . 4 8
9 6 4 6 -1 5 1 3 - 00 0 . . . . . . . . 2 9
9 6 4 7 -1 5 1 3 - 00 0 . . . . . . . . 2 9
9 6 4 9 -1 1 1 3 - 00 0 . . . . . . . . 2 9
9 6 5 0 -1 1 1 3 - 00 0 . . . . . . . . 2 9
TA - 00 0 7 . . . . . . . . . . . . 5 5
TA - 00 7 1 . . . . . . . . . . . . 5 5
TA - 01 0 5 . . . . . . . . . . . . 5 5
TA - 01 9 0 . . . . . . . . . . . . 5 5
TA - 02 3 4 . . . . . . . . . . . . 5 5
TA - 03 9 7 . . . . . . . . . . . . 5 5
Numbers ending with -0XX indicate connectors with various types on specified page.
-
8/12/2019 Radiall SMA 127-1
59/60
(203) 776-2813 FAX (203) 776-8294
APPLIED ENGINEERING PRODUCTS
www.aepconnectors.com [email protected] 59
About Applied Engineering ProductsSince our foundation in 1973, we have always believed that having our customers take a look inside AEP is important in
fostering strong vendor/customer relationships. We are proud of our physical plant and equipment, but even more so of our
dedicated staff. When customers see first-hand how AEPs people keep a constant focus on maintaining and improving
customer service and satisfaction, the rea-
son for our consistently strong on-time
delivery and quality records becomes clear.
We invite you to see for yourself. Call us to
arrange a plant touror, if you cant make
a visit, ask for your copy of INSIDE AEP,
our facilities and capabilities brochure.
-
8/12/2019 Radiall SMA 127-1
60/60
The SMA connectors in this brochure are only part of our
complete line of subminiature and microminiature
coaxial connectors and cable assemblies, including:
SMA
SMB
SMC
SSMB
SSMC
SLB (Slide-on version of SMB)
SSLB (Slide-on version of SSMB)
75 Snap-on mating
75 Screw-on mating
Adapters within and between series
Flexible cable assemblies
Semi-rigid cable assemblies
And over 100 styles of MIL-PRF-39012 QPL connectors
in series SMA, SMB, and SMC
Call for your copy of our 184-page full catalog to see them all.