tugas jarkom router 3 1235010002
DESCRIPTION
jarkomTRANSCRIPT
TUGAS
JARINGAN KOMPUTER
MENGHUBUNGKAN 3 JARINGAN DENGAN 3 BUAH ROUTER
NAMA :
ABRIANTO NUGRAHA ( 1235010002 )
SISTEM INFORMASI – FTIUNIVERSITAS PEMBANGUNAN NASIONAL “VETERAN” JATIM
2014
Cara menghubungkan 3 Router
1. Kita buat dulu desainnya seperti gambar ini (untuk tiap devicenya pakai yang generic)
2. Atur IP Addess untuk tiap-tiap PC nya:
- klik PC0 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC1 pilih tab desktop lalu IP Configuration dan atur seperti ini :
klik PC2 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC3 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC4 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC5 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC6 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC7 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC8 pilih tab desktop lalu IP Configuration dan atur seperti ini :
3. Buat koneksinya, antara PC dengan SWITCH (gunakan yang generic) gunakan KABEL STRAIGHT , kemudian antara SWITCH dengan ROUTER (gunakan yang generic) juga gunakan KABEL STRAIGHT, lalu antara ROUTER dengan ROUTER gunakan KABEL SERIAL ( DTE ).Perhatikan interface yang dipakai ketika menghubungkan antara switch dengan router, disini untuk koneksi switch-router saya menggunakan interface fastethernet 0/0 pada routernya dan serial 2/0 untuk koneksi router 0 – router 1 dan koneksi router 1 – router 2, serial 3/0 untuk koneksi router 1 – router 0 dan router 2 – router 1
4.Pada Router 0 atur ip address dan subnetmask untuk interface fastethernet 0/0 dan mengatur ip address dan subnetmask untuk interface serial 2/0 serta mengatur ip route dengan cara klik Router 0 pilih tab CLI lalu ketik seperti ini :
INCLUDEPICTURE
"http://secercahcoretan.files.wordpress.com/2012/10/42.png?w=529"
5.Pada Router 1 atur ip address dan subnetmask untuk interface fastethernet 0/0 dan mengatur ip address dan subnetmask untuk interface serial 2/0 dan interface serial 3/0 serta mengatur ip route dengan cara klik Router 1 pilih tab CLI lalu ketik seperti ini :
6. Pada Router 2 atur ip address dan subnetmask untuk interface fastethernet 0/0 dan mengatur ip address dan subnetmask untuk interface serial 3/0 serta mengatur ip route dengan cara klik Router 1 pilih tab CLI lalu ketik seperti ini :
6. Sekarang kita coba ping dari PC0 ke PC3, PC6, klik PC 0 lalu pilih tab desktop terus pilih comand prompt :
7. Sekarang kita coba ping dari PC3 ke PC0, dan PC6 klik PC 3 lalu pilih tab desktop terus pilih comand prompt :
8. Sekarang kita coba ping dari PC6 ke PC0, dan PC3 klik PC 6 lalu pilih tab desktop terus pilih comand prompt :
Dari hasil di atas menunjukan reply sehingga routing sudah dikatakan berhasil.
SCRIPT UNTUK MENGATUR ROUTER
Router>en Router#configConfiguring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z.Router(config)#interface fastethernet 0/0Router(config-if)#ip address 1.5.0.1 255.255.0.0Router(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upRouter(config-if)#exit
Router(config)#interface serial 2/0Router(config-if)#ip address 2.10.0.1 255.255.0.0Router(config-if)#clock rate 64000This command applies only to DCE interfacesRouter(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial2/0, changed state to downRouter(config-if)#exit
Router(config)#ip route 2.5.0.0 255.255.0.0 2.10.0.2Router(config)#ip route 3.5.0.0 255.255.0.0 2.10.0.2Router(config)#ip route 3.5.0.0 255.255.0.0 20.10.0.2
Router>en Router#configConfiguring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z.Router(config)#interface fastethernet 0/0Router(config-if)#ip address 2.5.0.1 255.255.0.0Router(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upRouter(config-if)#exit
Router(config)#interface serial 3/0Router(config-if)#ip address 2.10.0.2 255.255.0.0Router(config-if)#clock rate 64000This command applies only to DCE interfacesRouter(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial3/0, changed state to downRouter(config-if)#exitRouter(config)#interface serial 2/0Router(config-if)#ip address 20.10.0.1 255.255.0.0Router(config-if)#clock rate 64000This command applies only to DCE interfacesRouter(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial2/0, changed state to downRouter(config-if)#exit
Router(config)#ip route 1.5.0.0 255.255.0.0 2.10.0.1Router(config)#ip route 3.5.0.0 255.255.0.0 20.10.0.2
Router>enRouter#configConfiguring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z.Router(config)#interface fastethernet 0/0Router(config-if)#ip address 3.5.0.1 255.255.0.0Router(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upRouter(config-if)#exit
Router(config)#interface serial 3/0Router(config-if)#ip address 20.10.0.2 255.255.0.0Router(config-if)#clock rate 64000Router(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial3/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to upRouter(config-if)#exit
Router(config)#ip route 2.5.0.0 255.255.0.0 20.10.0.1Router(config)#ip route 1.5.0.0 255.255.0.0 20.10.0.1Router(config)#ip route 1.5.0.0 255.255.0.0 2.10.0.1% Invalid input detected at '^' marker.
Keterangan warna script:
Untuk mengatur ip address & netmask untuk interface fastEthernet 0/0 Untuk mengatur ip address & netmask untuk interface serial 2/0 Untuk mengatur ip address & netmask untuk route